 |
| |
|
|
|
| |
|
Capacity(mm) |
.gif) |
| |
|
Th. 0.8-2.0 |
| Wd. 2-6 |
TCH-3L-NS(W)
FOR HIGH TENSILE STRENGTH WIRES(w) |
Feed Speed(m/min)
10-30 |
| |
|
with Variator |
| |
|
Optimum for processing high in
tensile strength.
Since twisting is prevented by
causing the front and rear
straighteners to turn clockwise
and counter-clockwise,
sophisticated products can be
obtained. |
| |
|
|
|
|
| |
|
Capacity(mm)
Ø1-Ø3.2 |
 |
TCH-3L-FC
CLUCH TYPE |
Feed Speed(m/min)
10-20 |
With Variator |
| |
|
After measuring the length with an encoder, the line is cut with a
clutch without stopping. |
| |
|
|
|
|
| |
|
|
|
| |
|
Capacity(mm) |
 |
| |
|
Th. 0.8-2.0 |
| Wd. 2-6 |
TCH-3S-FP
CUTTING & PRESSING TYPE(P) |
Feed Speed(m/min)
10-30 |
| |
|
with Variator |
| |
|
Press working performed at the
same time as cutting.
Used for automobile wiper,etc. |
| |
|
|
|
|
| |
|
|
|
| |
|
Capacity(mm)
Ø0.8-Ø3.2 |
 |
|
|
Feed Speed(m/min)
7-15 |
| with Variator |
TCH-3L(NS)
SHORT LENGTH CUTTING TYPE |
NS Clutch cutting System |
| |
|
The NS system is such that the
cross section of the wire cut by
it is not damaged, leaving the
cross section almost true circle
as it is cut at right angles.
Thanks to this advantage, this
machine is widely employed
for processing of micro shafts
for small motors, VTR sets,
timer printers, floppy disks. |
| |
|
|
|
|
| |
|
|
.gif) |
TCH-3L(S)
CLUCH TYPE |
Capacity(mm)
Ø0.8-Ø3.2 |
Feed Speed(m/min)）
10-30 |
| |
|
|
| |
|
|
|
|
| |
|
|
|
| |
|
Capacity(mm) |
 |
|
|
Th. 0.8-2.0 |
| Wd. 2.0-6.0 |
BABY-F
FOR SPECIAL SHAPED
WIRES(Flat,Square,Hexagon,etc) |
Feed Speed(m/min)
10-30 |
| |
|
Exclusive for flat,square and
special wires,this machine
employs a leveler straightening
system that consists of a
vertical straightening roller and
horizontal straightening roller,
capable of providing high precision. |
| |
|
|
|
|
| |
|
|
|
| |
|
Capacity(mm) |
.gif) |
BABY-AL(S)
STANDARD TYPE |
Ø0.8-Ø3.2 |
Feed Speed(m/min)
30 |
| |
|
|
|
|
|
|
|
TCH-1(NS)
SHORT LENGTH CUTTING TYPE |
Capacity(mm)
Ø0.6-Ø1.8 |
 |
| |
|
Feed Speed(m/min)
5-15 |
| |
|
|
| |
|
|
| |
|
|
|
|
| |
|
|
|
| |
|
|
|
BABY-CS
STANDARD TYPE |
Capacity(mm)
Ø0.3-Ø1.8 |
 |
| |
|
Feed Speed(m/min)
20
|
| |
|
|
| |
|
|
| |
|
|
|
| |
|
|
|
| |
|
|
|
| |
|
|
|
|
| |
|
|
|
| NEW MODEL |
|
Capacity(mm)
Ø0.1-Ø0.5 |
 |
| TCH-05-W Ultra-thin wire cutting machine |
Feed Speed(m/min)
0.5-10 |
| |
|
Cutting of Ultra-thin
(0.1-0.5mm diamety)
wire which were considered
impossible in the past,is
made possible for both hard
and soft wire materials in
length ranging from 1mm-6000mm. |
| Features |
| |
|
|
|
|
| |
|
|
|
| |
|
|
 |
|
|
Capacity(mm) |
Pipe-Cutting Machine
GRINDING STONE FLYING CUT TYPE |
Ø0.5-Ø13 |
| Cutting length |
| |
|
500 over |
| |
|
|
|
|
Ø0.1-Ø3.2 Ø2.5-Ø6.0 Ø4-Ø9 Ø6-Ø28
UP
|
 |
